The Minimalist Woodworker. Vic Tesolin

always physically, on the shelf and on the floor,

      but in the dust bin between your ears—

      that’s where it begins.

      We all have the ability to walk the path less travelled.

      We can choose to say no, whenever we’re ready.

      We can make, instead of buy.

      We can fix it, instead of re-purchasing.

      Again and again, over and over.

      So to the minimalist thinker, the minimalist worker,

      the minimalist woodworker—

      Break it all down to the basics—

      breath in, breath out, one foot in front of the other.

      Choose your battles.

      Think long and hard before you bring something into your home

      and into your life—

      and don’t forget the workspace!

      From the wood you use in your woodshop;

      where you get it, how it’s harvested.

      The tools you hold in your hands.

      Even the joinery you use to hold your work together . . .

      how long do you think it will last?

      Does it matter?

      It certainly should, for you—as the maker.

      Will someone need to replace those things?

      Those tools?

      That bench?

      Is it an improvement?

      Can we do a little better?

      This book will help.

      minimal.

      If not literally in the toolkit, then metaphorically in the spirit of the craft.

      The minimalist woodworker—

      I raise my glass!

      “Make everyday a masterpiece.”

      — Tom Fidgen,

      The Unplugged Woodshop-Toronto, October 2015

      INTRODUCTION

      The truth about woodworking is that you don’t need a single machine or power

       tool to woodwork. There, I said it. What you do need is about 40 square feet

       of space for a workbench and some hand tools. That’s all you need to start making

       projects out of wood. You can work with even less space if you just want to make

       boxes, spoons, or other small projects but 40 square feet is a good start.

      And that’s a good thing. Some of us have little room to work with. Living in

       apartments, condominiums, and town homes means that we don’t necessarily have

       the space for a conventional wood shop. Even roomy homes have basements and

       garages that share space with cars and family overflow. The typical machines found

       in stand-alone shops are not possible to use in these smaller spaces. And can you

       imagine the backlash you would get from a neighbor in an apartment building if you

       fired up a router and a shop vacuum?

      WOODWORKING VS. WOOD MACHINING

      Machines have become a mainstream staple available to almost any consumer at

       many different price points. They are so ubiquitous that you can find them at home

       centers. And the common belief is that they are required to woodwork.

      I must admit that machines are handy, but they aren’t necessary. Machines, to my

       mind, are modern-day apprentices. They do the tasks that I don’t want to do. For

       example, a thickness planer speeds up the process of dimensioning lumber . . . but

       I don’t need one to get the job done. Machines are also quite adept at repeating

       operations, which makes them well-suited to production work. If you have to make

       25 tables it makes sense to spend the time to set up a machine to cut the joinery.

       But what if you are only making one table? In many cases it doesn’t make sense at

       all. Most of us are not production woodworkers so why have the production tools?

      I think we were lulled into the myth that power tools are more accurate than

       hand tools. In some cases this may be true but machines still need to be tuned and

       maintained to retain their accuracy. My question is—how accurate do you need

       to be? One of the characteristics of wood is that it is always taking on and losing

       water via the humidity in the air. A freshly dimensioned board can change over the

       time it takes to eat lunch so why pull out the calipers and micrometers to check

       dimensions? I think people feel that they can compensate for a lack of experience

       by trying to work to ultra-high tolerances to ensure success. I once had a student

       who was concerned when making a tabletop that one corner was thicker by 0.004"!

       That is the thickness of a piece of printer paper.

      The machines I choose to keep in my shop save me hours of hard labor but in

       the end, I could drop them all and still be able to woodwork.

      THE POWER OF THE HOBBYIST

      I hear many woodworkers describe themselves as ‘only a hobbyist’ when asked

       about what they do in the shop. The part I take exception with is the ‘only.’ Hobbyists

       think for some reason that they aren’t as qualified as a woodworker if they are

       not making money at it. I happen to think that some of the best woodworkers are

       those who don’t have the pressures of running a business looming constantly over

       their heads like a dark cloud. When I made furniture for a living I was constantly

       stressed about finishing one job and lining up the next one in order to make ends

       meet. Being a hobbyist allows you the freedom to explore new things and try new

       techniques without worrying about putting food on the table. You can spend time

       actually mastering skills. And if something doesn’t work out you can drill a hole in it

       and call it a birdhouse.

      About three years ago I started experimenting with axes—not juggling them while

       they’re on fire but using them as a way to remove material quickly. It took some time to

       learn how to sharpen and use axes but after some blood (literally) and sweat I worked

       it out. Now I use axes quite often in my shop. The point is, I would not have had the