You should now have a sheet of paper displayed on the screen.
This sheet is the size you specified in the “Page Setup”.
This sheet is in front of Model Space.
Rename the Layout tab
| N. | Right click on the Layout1 tab and select Rename from the list. |
| O. | Enter the New Layout name A Size |
| P. | Very important: Save as My Feet-Inches Setup again. |
| Q. | Continue on to Exercise 4C…..you are not done yet. |
EXERCISE 4C
CREATE A BORDER AND TITLE BLOCK
| A. | Draw the Border rectangle as large as you can within the dashed lines approximately as shown below using Layer Border. |
| B. | Draw the Title Block as shown using: |
1. Layers Border and Text.
2. Single Line Text ; Justify Middle in each rectangular area. (Hint: Draw diagonal lines to find the middle of each area, as shown)
3. Text Style= Text-Classic Text height noted.
Note: You can draw the Title Block in place and add Text with a rotation angle of 90 or Draw the Title Block horizontal, add Text and then rotate it. You decide.
| C. | Very important: Save as My Feet-Inches Setup again. |
| D. | Continue on to Exercise 4D…..you are not done yet. |
EXERCISE 4D
CREATE A VIEWPORT
The following instructions will guide you through creating a VIEWPORT in the Border Layout sheet. Creating a viewport has the same effect as cutting a hole in the sheet of paper. You will be able to see through the viewport frame (hole) to Modelspace.
| A. | Open My Feet-Inches Setup (If not already open) |
| E. | Draw a Single viewport approximately as shown. (Turn off Object Snap temporarily) |
| F. | Adjust the Viewport Scale as follows: |
F1. Confirm the Model button is showing.
F2. Select Zoom All
F3. Select the Viewport Scale of 1/4” = 1’-0” (Note: inches = feet)
| H. | Very important…. Save as My Feet-Inches Setup again. |
| I. | Continue on to Exercise 4E….you are not done yet. |
EXERCISE 4E
PLOTTING FROM THE LAYOUT
The following instructions will guide you through the final steps for setting up the master template for plotting. These settings will stay with My Feet-Inches Setup and you will be able to use it over and over again.
In this exercise you will take a short cut by importing the Plot Setup A from My Decimal Setup.dwt. (Note: If the Printer, Paper size and Plot Scale is the same you can use the same Page Setup.)
Note: If you prefer not to use Import, you may go to 3-17 and follow the instructions for creating the Plot- page setup.
| A. | Open My Feet-Inches Setup |
| B. | Select the A Size layout tab. |
You should be seeing your Border and Title Block now.
| D. | Select Import… from the Page Setup drop down menu |
| E. | Find My Decimal Setup.dwt as follows: |
E1. Select Files of type: Template [.dwt]
E2. Select My Decimal Setup.dwt
E3. Select Open button.
| F. | Select Plot Setup A from the Page Setups list. |
| H. | Select Plot Setup A from the Page Setup drop down list. (Note: It was not there before. You just imported it in from My Decimal Setup.dwt) |
| I. | Review all the settings. |
If the drawing appears as you would like it, press the Esc key and continue
If the drawing does not look correct, press the Esc key and check all your settings, then preview again.
Note: The Viewport will not appear in the Preview because it is on a no plot layer.
| K. | Select the Apply to Layout button. (The settings are now saved to the layout tab for future use.) |
| L. | If your computer is connected to the plotter / printer selected, select the OK button to plot, then proceed to N. |
| M. | If your computer is not connected to the plotter / printer selected, select the Cancel button to close the Plot dialog box and proceed to N. |
| N. | Important: Save the file again as My Feet-Inches Setup |
| O. | You are almost done….continue on to 4F. |
EXERCISE 4F
CREATE A NEW DIMENSION STYLE
1. Open
