Laboratory Methods for Soil Health Analysis, Volume 2. Группа авторов

(CaCO3) using concentrated H2SO4 or HCl.

      3 Weigh 0.50 mg of the soil into a silver vessel and add 5 drops or (5 mL) of concentrated H2SO4 or HCl.

      4 If effervescence is observed, inorganic carbon is present in the soil sample. If inorganic C is not present, go to Step 11.

      5 Treat soil containing inorganic C with 0.1 mL of 4N phosphoric acid solution.

      6 The treated sample should be allowed to dry for one or two days before analysis. Repeat steps for removal of inorganic C if necessary. Be cautious when handling the tins and do not use Al vessels as they will disintegrate when acid is added.

      7 Weigh 50 mg of soil into an aluminum tin capsule using an analytical scale with 0.001 precision.

      8 Fold the aluminum tin capsule containing the soil sample and load it on to the analyzer.

      9 Weigh a known standard to serve as a check, using one standard every 12 to 20 samples. Standards can either be EDTA, aspartic acid, or soil with a known concentration of C.

      * The operation of the analyzer should be operated according to the guidelines of the machine.

       Loss‐On‐Ignition (LOI) (Salehi et al., 2011; Schulte and Hopkins, 1996)

       Apparatus

      1 20 mL porcelain crucibles

      2 Forceps

      3 2000 μm sieve

      4 50 mL beaker

      5 Desiccator

      6 Muffle

      7 Analytical balance

       Procedures

      1 Air dry or oven‐dry soil at 35 to 40 °C.

      2 Carefully remove all plant and animal materials from the soil using forceps.

      3 Pass the soil through a 2000 μm sieve.

      4 Weigh 10 ( ± 0.05) g of the soil sample in a tared 50 mL beaker and oven‐dry at 105 °C overnight. This process will ensure the removal of all water from the gypsum in gypsiferous soils.

      5 Using a desiccator, cool the samples and then record the weight.

      6 Transfer the oven‐dry soil (~10 ( ± 0.05) g) into a porcelain crucible, heat the samples in a muffle furnace for 2 h at 360 °C (after the temperature reaches 360 °C).

      7 After the combustion, cool the samples to 150 °C in a desiccator before reweighing and recording the value

       Calculation

      SOM_LOI = [(soil weight after combustion – oven – dry soil weight) / (oven – dry soil weight) * 100]

      Soil Inorganic C

       Dry combustion Procedure

      1 Follow step 11 to 13 of the method for SOC to determine total soil carbon.

      2 Follow step 1 to 13 of the method for SOC.

      3 Soil inorganic carbon is calculated as the difference between total soil carbon and SOC.

      Other Analytical Methods and Issues Affecting Soil Carbon

       Gravimetric method for loss of carbon dioxide (Loeppert and Suarez, 1996)

       Apparatus

      1 50 mL Erlenmeyer flask

      2 Analytical balance

      3 10 mL and 250 mL pipettes or dispensers

       Reagents

      1 Hydrochloric acid (HCl), 3 M. Transfer 250 mL of concentrated HCl to 500 mL of deionized water and dilute to a total volume of 1 L.

       Procedure

      1 Weigh a stoppered, 50 mL Erlenmeyer flask containing 10 mL of 3 M HCl.

      2 Transfer a 1 to 10 g air‐dried soil sample (containing 0.1–0.3 g of CaCO3 equivalent) to the container, a little at a time, to prevent excessive frothing.

      3 After effervescence has subsided, replace the stopper loosely on the flask and swirl the flask occasionally for about 15 min.

      4 At intervals of about 15 min, remove the stopper and swirl the flask for 10 to 20 s to displace any accumulated CO2 with air.

      5 Replace the stopper and then weigh the flask and its contents to the nearest 0.1 mg.

      6 Repeat the agitation and weighing procedure until the weight of the container does not change by more than 1 to 2 mg. The reaction is usually complete within 1 h.

       Calculation

      1 Weight of CO2 = Difference between initial and final weights (flask + stopper + acid + soil)

      Biochar

      Biochar is a bioproduct from a thermochemical conversion (pyrolysis) of biomass (Koide et al., 2011). Biochar may be used as a soil amendment due to its chemical and physical characteristics, and because of its potential to help mitigate climate change. Sequestering biochar carbon in soil contributes greatly to reducing greenhouse gas emissions (Leng et al., 2019). Biochar has a high concentration of recalcitrant carbon that is resistant to decomposition (Glaser et al., 2002), but since a portion of most fresh biochar is easily decomposable (Lehmann and Joseph, 2015), and repeated analyses and applications of biochar may be necessary.

      Due to its chemical complexity and large variability, a simple routine way to quantify biochar in soils is still scarce and under investigation, mainly because of the difficulty in distinguishing biochar from other forms of soil organic matter. Methods to evaluate biochar in soils are extremely labor intensive or need specialized instrumentation. According to Leng et al. (2019), biochar in soils has been quantified by scanning calorimetry, nuclear magnetic resonance spectroscopy or infrared spectroscopy, analysis of molecular markers, or by preferential removal of inorganic and non‐biochar organic C by selective oxidation or acid treatment followed by the analysis of residual organic material by NMR, optical, or mass spectroscopy, or thermal conductivity.

      SOC Stocks: Considerations on Sampling Depth and Mass Corrections

      Soil carbon stocks are commonly quantified at fixed depths as the product of soil bulk density, depth, and organic carbon (OC) concentration. Soil C stocks are estimated using the following equation:

      C is the organic C stock in the soil layer (Mg ha^–1); OC is the total organic C content in the soil layer (%); Ds is the soil density in the soil layer (Mg m^–3), and E is the thickness of the sampled layer (cm). However, this method systematically overestimates SOC stocks in samples from areas with a higher bulk density, such as minimum tillage, thus exaggerating their benefits. This is not to discourage the use of such calculations, but rather to build awareness that estimates of real SOC change can be greatly compromised if bulk densities differ among treatments or over time.

References

      1 Albrecht, W. 1938.