Windows: A Book About Stained & Painted Glass. Lewis F. Day

of a face or the folds of drapery, which were not quite solid, and which consequently only deepened the colour of the pot-metal, and did not quite obscure it: he went so far even as to pass a smear of still thinner colour, a half tint or less, over portions of the glass which he wished to lower in tone. He began, in fact, however tentatively, to introduce shading. Happily he was careful always to use it only as a softening influence in his design, and never to sacrifice to it anything of the intrinsic beauty and brilliancy of his glass.

      The glass duly painted and burnt, the puzzle would be put together again on the bench, and bands of lead, grooved at each side to admit and hold the glass, would be inserted between the two pieces. These would be soldered together at the joints where two leads met; a putty-like composition or “cement” would be rubbed into the interstices between lead and glass to stiffen it, and make it air-and water-tight; and, that done, the window was finished.

      It would only remain (what would in practice have been done before cementing) to solder to the leads at intervals sundry loose ends of copper-wire, eventually to be twisted round the iron saddle bars let into the stone framework of the window to support it; it would then be ready to be fixed in its place.

      In contradistinction to the mosaic method of execution adopted by the thirteenth century glazier, a glass painter of the eighteenth century, and perhaps of the seventeenth, would, even though there were no necessity for longitudinal and latitudinal lines, cut up his window into oblong pieces of convenient size, only, of course, parallel and at right angles to one another.

      The sea he might or might not glaze in blue glass; here and there perhaps, but not necessarily at all, an occasional province might be leaded in with a piece of pot-metal; but for the most part he would use panes of white glass, and rely for the colour of the provinces upon enamel. He would have no need to separate his enamel colours by a line of lead, and where he wanted a dividing line he would just paint it in opaque brown. This method of glass painting forms an altogether separate division of the subject, not yet under discussion. It is referred to here only by way of contrast, and to emphasise the fact that, though we are in the habit of using the term stained glass rather loosely—though a stained glass window is almost invariably helped out to some extent by painting (unless it be what is technically known as “leaded glass” or “plain glazing”), and though a painted window is seldom altogether innocent of glass that is stained—there are, as a matter of fact, two methods of producing coloured windows, the mosaic and the enamelled; and that however customary it may be to eke out either method by the other more or less, windows divide themselves into two broad divisions, according as it is pot-metal or enamel upon which the artist relies for his effect.

      Between these two widely different ideals there are all manners and all degrees of compromise, and methods were employed which, to describe at this point, would only complicate matters. It will be my purpose presently to describe in detail the steps by which mere glazing developed into painted glass, and how painting came to supersede glazing; to show in how far painting was a help to the glazier, and in how far it was to his hurt; to describe, in short, the progress of the glass painter’s art, to better and to worse; and to distinguish, as far as may be, the principles which govern or should govern it.

      

      3. Ancient Arab Window.

CHAPTER III.

       GLAZING.

       Table of Contents

      The art of the glass painter was at first only the art of the glazier. To say that may seem like self-contradiction. But it is not so. On the contrary, it is almost literally the truth; and it is difficult to find words which would more vividly express the actual fact.

      We are accustomed to think of a painter as using pigment always in some liquid form, and applying it to wood or plaster, canvas or paper, with a brush. Should he lay it on with a palette knife, as he sometimes does, it is painting still. If he could by any possibility put together his colours in mid-air without the aid of paper, canvas, or other solid substance, it would still be painting. This is very much what the worker in stained glass, by the help of strips of intervening lead, practically succeeded in doing.

      As a painter places side by side dabs of paint, so the glazier put side by side little pieces of coloured glass. (Glass, you see, was the medium in which his colour was fixed, just as oil, varnish, wax, or gum is the vehicle in which the painter’s pigment is ordinarily held in suspension.) He could execute in this way upon the bench or the sloped easel quite an elaborate pattern in coloured glass; and although, in order to hold the parts together in a window frame, he had perforce to resort to some sort of binding, in lead or what not, he may still reasonably be said, if not actually to have painted in glass, at all events to have worked in it. In fact, until about the twelfth century, there were no glass painters, but only glaziers. Nay, more, it is to glaziers that we owe the glory of the thirteenth century windows, in which, be it remembered, each separate touch of colour is represented by a separate piece of glass, and each separate piece of glass is bounded by a framework of lead connecting it with the neighbouring pieces, whilst the detail added by the painter goes for not very much.

       4. Arab Window Lattice, Geometric.

      No strictly defined, nor indeed any approximate, date can safely be given at which the art of the glass-worker sprang into existence. Arts do not spring into existence; they grow, developing themselves in most cases very slowly. The art of working in stained glass can only have been the result of a species of evolution. The germ of it lay in the circumstance that glass was originally made in comparatively small pieces (there were no large sheets of glass a thousand years or more ago), and so it was necessary, in order to glaze any but the smallest window opening, that these small pieces should be in some way cemented together. It followed naturally, in days when art was a matter of every-day concern, the common flower of wayside craftsmanship, that the idea of putting these pieces together in more or less ornamental fashion, should occur to the workman, since they must be put together somehow; and so, almost as a matter of course, would be developed the mosaic of transparent glass, which was undoubtedly the form stained glass windows first took.

      It has been suggested that in some of the earliest windows the glazing is meant to take the form of tesseræ; but the examples instanced in support of that idea afford very little ground for supposing any such intention on the part of the first glass-workers. It may more reasonably be presumed that any resemblance there may be between early glass and earlier wall mosaic comes of working in the same way; like methods inevitably lead to like results.

      It is by no means certain, even, that the first glaziers were directly inspired by mosaic, whether of marble or of opaque glass. They were probably much more immediately influenced by the work of the enameller.

       5. Arab Lattice, Geometric.

      That may appear at the first mention strange, considering what has been said about the absolute divergence between mosaic and enamelled glass. But it must be remembered that enamelling itself among the Lombard Franks, the Merovingians, and the Anglo-Saxons, was a very different thing from what the Limousin made it in the sixteenth century. It was, in fact, a quite different operation, the only point in common between the two being that they were executed in vitreous colour upon a metal ground. The enamel referred to as having probably influenced the early glazier is of the severer kinds familiar in Byzantine work, and known as champlevé and cloisonné. In the one, you know, the design is scooped out of the metal ground, in the other its outline is bent in flat wire and soldered to the ground. In either case the resulting cells are filled with coloured paste, which, under the action of the fire, vitrifies and becomes embodied with the metal. In champlevé enamel naturally the metal ground is usually a