Plastics Process Analysis, Instrumentation, and Control. Группа авторов

Figure 1.3 Mold-cooling system (39).Figure 1.4 Induction heating assembly (54).Figure 1.5 Mold thermal controlling device (56).Figure 1.6 Steam cracking process (93).

      2 Chapter 2Figure 2.1 Monomers for zwitterionic polymers.Figure 2.2 Amines for dendritic molecules.Figure 2.3 Oil removal vs. settling time of benzyl-G3.0 (47).Figure 2.4 Oil removal vs. settling time of octyl-G3.0 (47).Figure 2.5 Polymer dosage vs. settling time (47).Figure 2.6 Experimental environment (65).

      3 Chapter 3Figure 3.1 Injection molding engine (4).Figure 3.2 Reaction injection molding process (118).Figure 3.3 Concept of a self-optimizing injection molding process (127).Figure 3.4 Multilevel control system architecture (8, 132).Figure 3.5 Flow curve of shear viscosity versus shear rate (147).Figure 3.6 Change in shrinkage with the increase of injection cycles (152).Figure 3.7 Side view of an EPS recycling and extruding device (193).Figure 3.8 Methylene blue.Figure 3.9 Injection molding machine with a nozzle valve (216).Figure 3.10 Sectional view of a hot runner mold (218).

      4 Chapter 4Figure 4.1 Schematic architecture of the embedded thermocouple (4).Figure 4.2 Schematic diagram of an RTD circuit (24).Figure 4.3 Take-away conveyor (36).Figure 4.4 Monomers for a multilayer polymer system.Figure 4.5 Chlorhexidine.Figure 4.6 Side view of a delivery assembly (72).

      5 Chapter 5Figure 5.1 Perspective view of a nozzle (2).Figure 5.2 Mold design (5).Figure 5.3 Nonlinear response (16).

      6 Chapter 6Figure 6.1 Framework of a typical experimental design (1).Figure 6.2 Setting the initial process parameters with CBR (1).Figure 6.3 Organosilanes.Figure 6.4 Single-screw extruder (53).Figure 6.5 Block diagram of the blown film extrusion apparatus (92).Figure 6.6 Nip roll assembly (94).Figure 6.7 Horizontal stack configuration (95).Figure 6.8 Drugs for testing.Figure 6.9 Continuous filter (122).Figure 6.10 Screen changer device (123).Figure 6.11 Wheel-type blow molding machine (124).Figure 6.12 Pressure transducer (131).Figure 6.13 Piezoresistive thin-film sensor system (136).Figure 6.14 Schematic diagram of the gas flow (146).Figure 6.15 Rotary thermoform drum (164).Figure 6.16 Organic phosphites.Figure 6.17 Hindered amines.Figure 6.18 Antioxidants.

      7 Chapter 7Figure 7.1 Centrifugal dryer (7).Figure 7.2 Plastic pellet dryer with control system (11).Figure 7.3 Friction puller (14).

      List of Tables

      1 Chapter 1Table 1.1 Cost classification techniques (3).Table 1.2 Recent review articles and their targeted scope (3).Table 1.3 Plastic waste from various countries (65).Table 1.4 Floating debris (66).Table 1.5 Feed materials, liquid mixture (93).Table 1.6 Feed materials, gas mixture (93).Table 1.7 Cracked products from gas material and naphtha (93).Table 1.8 Cracked products from liquid material and naphtha (93).

      2 Chapter 2Table 2.1 Modulus and relative moduli for uniaxial compression.Table 2.2 Components of a PAGAT polymer (46).Table 2.3 Molar ratios of acrylamide to HADE.

      3 Chapter 3Table 3.1 ABS 780 (Kumho Chemicals Inc.) (16).Table 3.2 Controllable variables (54).Table 3.3 Analysis of variance for shrinkage of POM (102).Table 3.4 Design variables (118).Table 3.5 Three-level variables for modeling (8).Table 3.6 Material properties (174).Table 3.7 Circumference (175).

      4 Chapter 4Table 4.1 Peak removal force and probe distance (66).

      5 Chapter 5Table 5.1 Specifications of Common Heaters (16).

      6 Chapter 6Table 6.1 Expert system-based methods (1).Table 6.2 History of polymer processing technologies (24).Table 6.3 Major control approaches for continuous single-screw extrusion (54).Table 6.4 α-Olefin comonomers (96).Table 6.5 Processing parameters in the cast film production (93).Table 6.6 Standards for plastic pipes.Table 6.7 Performance results of the tested algorithms (152).Table 6.8 Phosphites and phosphonites (167).Table 6.9 Hindered amines (167).Table 6.10 Antioxidants (167).Table 6.11 Peroxide scavengers (167).Table 6.12 Yellowness index and impact strength (167).

      7 Chapter 7Table 7.1 Typical drying conditions for thermoplastic materials (3).Table 7.2 Checklist for the efficiency of a dryer system (3).Table 7.3 Polymers for drying.

      Guide

      1  Cover

      2 Table of Contents

      3  Title Page

      4  Copyright

      5  Preface

      6  Begin Reading

      7  Index

      8  End User License Agreement

      Pages

      1  vii

      2  ii

      3  iii

      4  iv

      5  v

      6  vi

      7  1

      8  2

      9  3

      10  4

      11  5

      12  6

      13  7

      14  8

      15  9

      16  10