Gun Digest’s Double Action Trigger Concealed Carry eShort. Grant Cunningham

      

      Contents

       Cover

       Concealed Carry: Double Action Trigger

       Copyright

      Bring the pad of the support hand thumb down on top of the shooting hand’s thumbnail. Adjust as necessary to get the specified contact points and make a mental note of how everything feels. It’s that feeling that you’ll want to replicate each time you grasp the gun.

      Believe it or not, there was a time in the history of the double action revolver when it was widely supposed that it couldn’t be shot accurately. Over the years we’ve come to learn that it just isn’t true, and today many instructors say that learning to shoot a double action is the key to shooting all handguns well.

      That’s what this chapter’s about. Shooting a double action revolver well is all about mastering the heavy, long trigger travel. I’ve often said that the revolver is the easiest gun to shoot, but the most difficult to shoot well. The trigger is the reason, but it’s far from impossible to conquer. It’s just a matter of paying attention to the basics.

      If you’ve read my introduction, you’ll remember the story about the falling plates. There is a lesson to be learned, and I hope you’ll take it to heart: you have to commit yourself to shooting double action. It’s all too easy to allow yourself to cock the gun to single action in order to make a shot you’ve been missing in double action. Resist that temptation! Every time you take the easy way out you stop your forward progress. Even at the end of a practice session, don’t succumb to the idea that you need to leave on a high.

      The only way to master double action is to always shoot in double action.

       It starts with grasp

      Think about this: a six-shot revolver might weigh something in the neighborhood of 38 ounces or so; that’s about 2-1/4 pounds. The trigger weight on that gun will typically be something around 12 pounds. It doesn’t take a math whiz to realize that the shooting hand will need to control about 9-3/4 pounds of excess force, and it needs to do so over a travel of perhaps 3/4 of an inch.

      If the grasp isn’t solid, that extra 9-3/4 pounds of force is going to push the gun around in the hand(s). The grasp has to be strong enough to control that nine pounds of force applied to the trigger, and it just can’t be done with the kind of light ‘handshake’ hold advocated by target shooters!

      It’s necessary to tighten this grasp to hold the gun steady during actual shooting. Hold the gun at arm’s length and squeeze with both hands. Increase the pressure until your hands shake from the effort, then back off the pressure just enough to stop the trembling. You’ll notice that this is much more pressure than you would otherwise exert, and it is the amount you need to apply every time you achieve your shooting grasp.

      You’ll find, with even occasional practice, that your muscles will rapidly develop from this isometric exercise. The strength of your grasp will increase and you’ll have increasing control over your gun.

       Big hands - little gun

      On occasion I’ll encounter a shooter whose large hands and small gun present a challenging mismatch. In these cases it can become difficult, if not impossible, for the trigger finger to complete the trigger stroke without bumping into the support hand thumb. In these cases I recommend that the support thumb be placed higher on the shooting hand thumb, on or just past the first thumb knuckle. This is usually sufficient to cure interference issues.

      In some cases even that isn’t enough. For those with very large hands it can sometimes be necessary to wrap the thumb around the backside of the gun, crossing the backside of the shooting hand thumb.

      This is recommended only in very rare cases, because it presents a couple of risks. First, if shooting a revolver with a hammer it’s easy for the thumb to interfere with the hammer spur. This can keep the hammer from traveling back far enough, effectively preventing the gun from firing.

      Second, if the person in question also owns autoloading pistols and mistakenly does this while shooting one, his thumb can suffer severe lacerations from the rearward moving slide. In such cases it’s not unusual to have the damage go clear down to the bone. I only recommend this technique for people who absolutely need it, and absolutely will not be shooting autoloading pistols.

      Sometimes I find shooters with very long thumbs, where the trigger finger actually contacts the shooting hand thumb even with the thumb curled down. In these cases it’s necessary to modify the finger placement on the trigger, using the pad of the finger rather than the first joint. This is less desirable because of the reduced leverage the trigger finger can employ, but it is occasionally the only way to be able to shoot the gun.

      Attaching oversized grips, particularly if fitted to the individual’s hand, is usually the best way to address these problems. Properly sized grips can go a long way in eliminating some of these problems.

      While one’s choices in weaponry can be a touchy subject, in the cases of severe size mismatch the best solution is often to get a different gun. Of course that means changes to accommodate the lessened concealability, but is at least worth consideration.

       Finger placement is critical

      Back in Chapter Two I mentioned that fitting the gun to the hand was important to be able to shoot a revolver well, and that the key to fitting was the trigger finger’s position on the trigger. If you haven’t read that chapter to verify that your gun fits your hand, please go back and study. With the amount of force and movement that the revolver requires of your trigger finger, the better the gun fit the easier trigger control will be.

      While occasionally there will be some mild disagreement from small segments of the revolver community, most trainers I’ve met recognize that the optimum trigger finger position is at the first joint (known as the distal interphalangeal joint, for the anatomy students in the audience.) Some trainers go so far as to call this the ‘power crease,’ because it seems to result in more force being applied by the muscles.

      Like so many others, I’ve found that this position – ideally centered on the trigger face – gives the best combination of leverage against trigger weight. This mechanical advantage also allows for better control of the trigger. The finger doesn’t tire as quickly, and movement is smoother. With a little bit of practice, the first joint placement allows the shooter to manipulate the trigger with as little imparted motion to the gun as possible.

      In times past it was taught that the pad of the finger should be the surface that pressed on the trigger. While there are still a few prominent (and very successful) shooters and trainers who champion this method, I think it’s safe to say that the majority opinion has long since shifted to the distal joint position, and not just for revolver shooting.

      As I’ve mentioned, a gun that is a bit small for the hand is much easier to deal with than one which is too large. If yours is too large, or perhaps just borderline, consider a change in either the grips or the gun itself to something which better fits your for the job of practicing trigger control. Once you’ve mastered the double action trigger you can make do with a large gun, but starting out with such a size mismatch makes learning more difficult.

       Terminology and preferences

      In the following discussion I use some very specific terminology for the act of moving the trigger. There are also terms I don’t use for very specific reasons, mainly because they’re either not descriptive or put the wrong preconception into the shooter’s mind. Is this point of view overblown? Some might say so, but I believe that when learning to perform a physical skill a solid, consistent